Max. Pressure

•      •  5 metric tons (10 MPa on pressure gauge).

Hydraulic Electrical Presser

• 
       •  Piston diameter: 60 mm.
•      •  Vertical move distance: 35 mm.
•      •  Automatic pressure controller
•      •  Please click on the picture for details。

Induction Heater

• 
       •  Working voltage: 208 - 240 VAC, 50/60 Hz, three phase (380V three phase available upon
          request)
  
•      •  Working current: 40 A (with a 60 A breaker).
•      •  Maximum input power: 15 kW.
•      •  Output frequency: 30 ~ 80 kHz.
•      •  Duty cycle: 80%.
•      •  Max. Working Temperature :  1600 ℃ max duration time: < 30 min.
•      •  Ultimate Temperature: 1700 ℃ <1 min. (This might cause damage of thermocouple)
•      •  Air cooling: fan.
•      •  Protection: water pressure monitoring, high-temperature protection, and overpower protection.
  
  

Temp. Controller

• 
       •  Working voltage: 208 ~ 240 VAC, single phase.
•      •  Precision digital temperature controller with automatic PID tuning.
•      •  Temperature profile that contains maximum 30 programmable segments to control heating,
           dwelling, and cooling.
•      •  Overheating and thermocouple failure protection.
•      •  Temperature accuracy: ± 3 ºC.
•      •  B-type thermocouple.
•      •  Continuous working temperature range: 1000 ~1600 ºC.
•      •  lower temperature range (300 - 600oC) is available upoon request.
•      •  Maximum heating rate in vacuum (only for 0.5" inner diameter graphite pressing die; without
          any thermal block):
•          º  4      ºC/s    ( 4 mins 50 seconds from room temperature to 1200 ºC)  
•          º  2      ºC/s    ( 5min 40 seconds from 1200 to 1300 ºC)
•          º  1.5   ºC/s    ( 6min 46 seconds from 1300 to 1400 ºC)
•          º  1.2   ºC/s    ( 8mins 10 seconds from 1400 to 1500 ºC)
•          º  1      ºC/s    ( 9mins 50 seconds from 1500 to 1600 ºC)
•      •  Experimental cooling rate in vacuum:
•          º  3.5    ºC/s   (~ 2 mins 20 seconds from 1600 to 1200 ºC)
•          º  1.1    ºC/s   (~ 8 mins 10 seconds from 1200 to 800 ºC)
•          º  0.4    ºC/s   (~ 21 mins 25 seconds from 800 to 500 ºC)
•          º  0.16  ºC/s   (~ 37 mins 15 seconds from 500 to 350 ºC)
•          º  0.06  ºC/s   (~ 104 mins 20 seconds from 350 to 150 ºC)
  
  

• 
       •  Stainless steel vacuum sealed chamber: 260 × 230 × 320 mm (OD × ID × L).
•      •  Flanges on both ends of the chamber. Flanges have a tunnel for cooling water.
•      •  Equipped with a KF-25D vacuum port, pressure gauge, 1/4" gas inlet port with the stainless steel
          needle valve.
•      •  The upper flange can be lifted by raising the lead screw which provides the easy access to
          retrieve the graphite die.
•      •  Requires at least 55 liters per minute water flow. Please click on the picture below to order at
          an extra cost.
•      •  Vacuum level: up to 10-5 Torr by our molecular pumping station (EQ-PAC-LD turbo pumping
          system pump)  or 7.5 mTorr by a mechanical pump.   10-7 torr turbopump system is available
          upon  request
•      •  Vacuum pumped is not included.  Please click on the pictures below to view our vacuum pumps
          at extra cost.
  
  

                              

• 
       •  Two built-in graphite supporting rods with Max pressure 50 Mpa
  
•      •  One set of 0.5" (inner diameter) graphite die are included for immediate use.
•      •  Made of high purity graphite by HIP processing,  Max. Load from the hydraulic press is dependent
          on die 's ID
•          º  0.5"ID   Max.  0.5T ( sample pressure 50 Mpa )
•          º  1.0 ID:   Max.  3T ( sample pressure 50 Mpa, which is optional)
•      •  The graphite pressing die is fragile and consumable. Please click on the picture below to order
          extra sets. We also provide customized die sets upon customer request at extra cost.
•      •  Mica spacers are used to adjust the height of die sets and insulate heat. Please click on the
          picture below to order spares.
  
  

                             

•      •  Note: The maximum pressure range of graphite dies will vary depending on the inner diameter of
         the die. For example, the graphite dies with an inner diameter of 0.5" can withstand 0.6 metric
         tons. For the graphite die with an inner diameter of 1" can withstand 3 metric tons.
•      •  If use high-quality SiC dies, the pressure can reach 100 MPa. Please contact your local supplier
          for SiC die that MTI does not supply
  
  

    Dimensions 

•      •  800 × 800 × 1300 mm (L × W × H).  

    Net Weight

•      •  350 kg.

 
   Shipping Weight & Dimensions

• 
       •  Two Pallets
  
•      •  935 lbs; 47" x 39" x 71"
  
•      •  420 lbs, 48" x 40" x 54"
  
  

 
    Application Notes

• 
       •  Attention: the gas cylinder must have a two-stage pressure regulator to limit the pressure below
          3 psi for safe operation. Click here to learn the installation of a gas regulator.
  
  

• 
       •  Lifetime support.
•      •  One year limited standard warranty (extend the warranty to 5 years at extra cost).
•      •  Graphite rods are not covered by warranty.
  
  

• 
       •  CE certified.
•      •  NRTL certification (UL 1450) is available upon request at extra cost. Please contact our sales
          representatives for quote.