Furnace & Power
|
• Splitable Eight heating zone tube furnace with air cooling layer- • High quality fibrous insulation and reflective coating for max. energy saving.
- • Power: 208 - 240VAC 50/60Hz, Single Phase, 12KW max. (circuit breaker which is rated
@ 80amps or higher is recommended)
|
Heating Zone |
• Ten heating zones: 150mm / zone- • Total heating zone length: 1500mm
- • Constant temp. zone: 900mm ±5°C
|
Working Temperature |
• 1100°C max.for < 1hr - • 1000°C for continuous
- • Heating rate: ≤10°C/min
|
Temperature Control
|
• Ten digital temperature controllers to control each heating zone- • Each channel is with PID auto-tuning, up to 30 segments programmable
- • Built-in overheating & thermocouple failure protection.
- • +/- 1 ºC temperature accuracy.
|
Heating & Cooling Rate |
• Heating: 0-200℃ ≤10℃/min , 200-700℃ ≤6℃/min, 700 -900℃ ≤3℃/min, 900-1100℃≤1℃/min- • Cooling: 200-800℃ ≤10℃/min , 800-1100℃ ≤5℃/min
|
Thermocouple
|
• Omega 3mm OD K Type with high-temperature (220°C) connector- • Total 10 TCs, one for each zone
|
Process Vessel
 |
• The pressure vessel is made of Nickel-based superalloy GH747
(Click to download GH747 nickel-based alloy datasheet)
- • Vessel size: OD 85 x ID 45 x Length 2400 (mm)
- • Optional: torque wrench is available here to avoid over-tighten the flange bolts.
Please click the image on the left to order. - • Warning: Never put a sample inside tube directly without crucible or isolated foil to avoid sample
react with tube alloy.
|
Working Pressure |
• 15 Mpa max. at <800°C- • 10 Mpa max. at <900°C
- • 6 Mpa max. at <1000°C
- • 4 Mpa max. at <1100°C
- • Never heat up above 1200°C
|
Working Gases |
• Inert gas and oxygen- • No hydrogen or any flammable gas
|
Flange and Fitting
|
• Two CF type flanges are weld with female 1/4"NPT fitting to connect high-pressure tube- • 2 pcs Copper o-rings are included ( spare copper O-ring is available as consumable )
|
Gas Flow & Pressure Control System
|
• Gas flow and pressure control system is built in the separated unit with digital display ( see pic left )- • Two pressure sensors and digital displays are installed to monitor the pressure for gas inlet and furnace tube
- • One high-pressure mass flow controller is installed at the gas outlet to control gas flow rate with max.
10Mpa working pressure and 500 SCCM flow rate - • Pressure relief valves are installed to ensure safety. The valve will release gas when the pressure reaches
the setting point.
|
Dimension & Weight |
• Dimension: 26000mmL*700mmW*947mmH (furnace); 1100mmL*600W*1200mmH (control consol)- • Net weight: 480 kg
|
| Operation Instruction |  |
Compliance and Warranty |
• NRTLNRTL or CSA certificate is avaialble upon request at extra cost
  
- • One year limited warranty for lifetime support
|
Application Notes |
• Hytort Application, or named Hydroretorting of Shale Oil is a process developed by IGT to double the yield of
shale oil and hydrocarbon gases. MTI High-Pressure furnaces with Ni-based superalloy tube is an ideal
tool for conducting related experiments. Please click underlined to view research paper.
|
Safety Notes |
• Ni-based Superalloy ( Waspaloy or equivalent) is a reliable processing tube which can be used under high
temperature and high pressure.. It has excellent ductility and tensile property so only creep deformation
happens under overpressure destruction test and following by a crack formed (usually at the hot zone at the
center of tube) to release the pressure. Brittle fracture won’t happen in the overpressure destruction test
which means no tube explosion will happen under overpressure of inert gas or safe gas or under other
accidents causing overpressure of inert gas or safe gas.
Above pics show Ni-based Super-alloy ( Waspaloy or equivalent) processing tube under overpressure test
- • Attention: For the use with flammable, toxic or corrosive gases, you must contact MTI engineering
group for the consultation to know all the prerequisites and precautionary measures.
- • Attention: A two-stage pressure regulator must be installed on the gas cylinder to limit the pressure to
below 3 PSI for safe operation. Please click here to learn how to install the gas regulator.
|
