| |
Inside Chamber Size | - Heated chamber: 200 x 200 x 200 mm (8x8x8 inch), 8 Liter.
- Energy-saving 1800 grade fibrous alumina insulation.
- High purity Al2O3 coating.
|
Power | 7.5 KW
|
Voltage | AC 208 - 240V single phase; 50/60 Hz |
Current | 36 Amp (50 Amp air breaker is required) |
Continuous Working Temperature | 1650°C |
Maximum Working Temperature | 1700°C (< 1 hr) |
Heating Rate | 5°C / min |
Temperature Accuracy | +/- 1°C |
Thermocouple | two B type thermocouples (control thermocouple and secondary alarm thermocouple) |
Temperature controller
 | Main Temperature Controller is used to setting and running the 30-segment heating program and provides the 1-level temperature alarm protection.
Secondary Temperature Controller reads the temperature from the secondary B type thermal couple, monitors the temperature during all process and provides the 2-level temperature alarm protection. |
Pressure Control | - The pressure sensor and pressure controller are installed. It reads the chamber pressure and controls the inlet and outlet gas valves respectively according to the pressure limit settings.
- The pressure control can be used to perform the following functions:
- Purging
- Pressure control
- High and Low-pressure protection
- The pressure controllable range: -0.06 to 0.03Mpa.
|
Heating Elements
and
Working gas | - 6 pcs Mo Alloy coils (can only be used under inert gas, Ar is preferred; cannot be used under air or oxygen at the temperature > 300°C).
- Optional: If using with pure oxygen gas, must use MoSi2 heating element with Ni power connection wire。 Please call us in advance for the modification
 |
Temperature Control
| - PID automatic control via SCR (Silicon Controlled Rectifier) power control with phase angle fired, current limiting resistor.
- 30 programmable segments for precise control of heating/cooling rate and dwell time.
- Over-temperature protection and thermocouple failure alarm functions allow operation without attendant(s).
- +/- 1ºC temperature accuracy.
- RS485 Communications Port.
|
The temperature controller (optional)
 | - MTS02-Y Temperature control software kit (for YD518P series controllers) + brand new laptop package is available at the options bar. Click for the detail information about the MTS02-Y software kit.
- You may upgrade the temperature controller to the Eurotherm Temperature Controller which is fully compatible with LabVIEW with +/- 0.1oC accuracy. This package includes a Eurotherm programmer, a communication cable (RS485 - USB) and a software CD. Click the pic left to view the full spec of the Eurotherm temperature controller.
|
Pressure Relief Valve
| Spring Loaded Type Pressure Relief Valve
- Cracking pressure is manufacturer pre-set at 0.066Mpa (relative pressure value).
- Valve close pressure: 0.03Mpa (relative pressure value).
- Max. Temperature 200ºC.
- 35mm O.D barb fitting for gas exhaust.
|
Gas Flow Control and
Vacuum Valve
| - Two flow meters (#1: 0~8L/min; #2: 0~4L/min) are installed on the front panel of the furnace.
- One heavy-duty vacuum pump (CE certified) is built on the bottom of the furnace.
- Optional: You may order a (UL certified) pump at extra cost (Pls click the right picture below to see specs).
 ( CE certified )  ( TUV certified ) |
Water Cooling
| - A 16L/min recirculating water chiller is installed in the bottom of the furnace for cooling furnace sealing flange (CE certified only)
- MET Certification (UL 1450) for water chiller is available upon request at extra cost, please contact our sales representatives for a quote.
|
Net Weight | 475Kg |
Shipping Weight | 1200 Lbs.
|
Product Dimensions
|  Please click the picture on the left to view dimensions:
|
Shipping Dimensions | 58" x 46" x 89" |
Warranty | One year limited warranty with lifetime support. (Consumable parts such as sample plates and heating elements are not covered by the warranty, please order the replacement at related products below.) |
Compliance | - CE Certified for the furnace, vacuum pump, and water chiller.
- NRTL (UL61010) or CSA certification is available at extra cost.（ please click mark below to learn details
-
  
|
Application Notes | |
Warnings | - ATTENTION: Any damages caused by the use of corrosive and acidic gasses are not under the coverage of MTI One Year Limited Warranty.
- In order to prevent oxidation/corrosion damages to the Mo heating elements, it is necessary to keep a constant inert gas (Ar preferred) flow throughout the entire process. This is the most effective way to carry out any by-products.
|
Operation Instructions | |
