Working Voltage | 208 - 240 V AC, 50/60Hz, Single Phase
|
Max. Power Consumption | 4 KW ( 30A Air breaker required ) |
Max. Coating Width | 250mm |
Thickness adjustable range | 0-5mm
|
Coating thickness (after drying) | 30 - 200um (for most kinds of battery electrode coating material)
Note: The dried coating thickness results vary depending on the physical property of the coating material.
|
Thickness Precision | ± 3µm (± 5µm at edges)
|
Coating Speed | 0-750 mm / minute |
Max. Drying Temperature
| 120°C
( Using a 240V transformer, can reach 150°C max.) |
Temperature Accuracy | ±1°C |
Heating Zone Length | 710mm (28") |
Reeling/Unreeling Shaft
| 75mm (ID) |
Max. Reeling/Unreeling Diameter | 250mm (OD)
|
Max. Coating Length
|
• Depending on the coating and substrate thickness.- • Typically, 10um thick foil with 100um coating can get
600 meters of electrode length coated per run
|
Coating Modes
|
• Using transfer coating technique ( Reverse comma )
for better uniformity ( Click Pic below -left for detail )- • Two available coating modes selectable on the control
panel. - º Continuous mode
- º Intermittent coating ( system performs
coating, stops, coats again and so on. The
length of the coating and break segments
can be specified by the user ).
  
 |
Slurry Stirring
|
SS316 Moving Rod
|
Exhaust Port Size | 127mm O.D |
Compressed Air
|
0.5-0.8 MPa (Air compressor not included. Please click here to order)
Attention: If a gas cylinder is used instead of air compressor(pic2), a two-stage pressure regulator(pic1) must be installed on the gas cylinder to limit the pressure within the required working range for safe operation. Click here to learn the installation of a gas regulator.
 pic1  pic2
|
Optional
• Reference article of the
plasma surface treatment
applied in battery electrode web
coating process Superior
Performance of LiFePO4
Aqueous Dispersions via Corona
Treatment and Surface Energy
Optimization
|
• You may order Dual-Filtration System for NMP
Vapor and connect it to the coating system for
keeping environmental healthy. Please click
Pic.1 for details.
• Atmosphere plasma cleaning add-on for the
substrate is available upon request. Such a
surface treatment will activate and increase the
energy of the substrate surface and thus
enables a better adhesion & bonding to the
coating materials. Please click Pic.2~3 and
Video.1 for more details.
 Pic.1  Pic.2
 Pic.3 
 Video.1
- • Test the flexibility of the coated electrode with EQ-MBT-
12-LD mandrel bending tester. ( Click pic.4 in below for
detail.) - • You may use Precision Peristaltic Slurry Feeding
Pump for continuous slurry delivery during the roll to
roll coating process.( Click Pic.5 & Pic.6 in below to
order ) - • You may order the Magnetic De-ironing Filtration
system (Pic.7) for optimizing the battery electrode
slurry condition before the coating process.
 Pic.4  Pic.5
 Pic.6  Pic.7
|
Product Dimensions
|
 1620mm ( L) x 950mm (W) x 1100mm (H)
|
Compliance
|
• CE Certified- • NRTL (UL61010) or CSA certification is available
upon request at extra cost.
 
|
Warranty | - • One Year limited warranty with lifetime support
- • Rusting and damage due to improper storage
condition or maintenance are not covered by warranty
|
Operation Manual & Video |
 
  |
Application Notes |
• Please use Acetone to clean and dry the doctor blade,
slurry feeder, and roller to avoid rusting- • Please contact us for compatibility of slurry solvent
and rubber roller of the coater. - • Customers are welcome to visit our facility to receive
technical training before shipping of equipment
(Please schedule an appointment with us in advance) - • On-site Training is available for customers at extra
cost.
- • Test the flexibility of the coated electrode with EQ-MBT-
12-LD mandrel bending tester.
( Click pic.1 below for detail.) - • PET Film with single side Si Coating is available for
Roll-to-Roll tape /slot die/ Micro Gravour casting of Li-
ion battery electrode slurry, ceramic, functional resin,
ink, and others. Please click the Pic.2 in below to view
the product.
Pic.1  Pic.2 |
| Net Weight | 1000 kg (2200 lbs) |
| Shipping Dimension | 70" x 45" x 55" |
