2.375" x 40" (60.5 OD x 51.5 ID x 1000mm L)

3.15" x 40" (80 OD x 74 ID x 1000mm L)

This model of furnaces have passed the UL61010 or SPE 1000 certification and are currently in stock. No extra certification fee. Certificate report will be sent along with the furnace.

• 
       •  Double layer steel casing with air cooling.   
•      •  Two cooling fan inside to keep  case temperature < 55ºC.  
•      •  High purity Alumina refractory chamber with 10mm thick 2500ºC grade YSZ ceramic liner.  
  
  

• 
       •  PID automatic control via SCR (Silicon Controlled Rectifier) power control with phase angle fired, current
          limiting resistor.
•      •  30 programmable segments for precise control of heating rate, cooling rate and dwell time.
•      •  Please click here to learn why SCR is more accurate than SSC (Solid state relay).
•      •  Built-in over temperature alarm and protection allows for operation without an attendant.
•      •  +/- 1 ºC temperature accuracy.
•      •  RS485 Communication Port.
•      •  Optional:  
•      •  The furnace may be operated by PC by installing a control module. Please order an MTS-02 control
           module at extra cost.  
  
•      •  If you order the PC control module together with the furnace, we will install and test it before shipping.
           We recommend you to order a computer (laptop) from us to avoid software installation problems.
           For more information please click here.
  
  

                              

• 
       •  One pair of sealing flanges with double silicone high-temperature O-rings is included.
•      •  Two SS needle valves and one dial vacuum gauge are installed on flanges for immediate use.
  
  

               

• 
       •  Standard 1/4‘’ Barbed fittings with needle valves.
•      •  For supplying high-pressure gas, you may replace the standard barbed hose fitting with the 304SS 1/4"
          Swagelok® Tube Fitting, please click underlined to order.
•      •  Optional: In order to increase the throughput and achieve high vacuum, you may replace the standard barbed
          hose fitting with the KF25 adapter, please click the underlined to order.
•      •  Optional: You may also consider using the parts in below to increase the vacuum efficiency
•      •  Please click here to order digital vacuum gauge for precision vacuum control up to 10^-4 torr 
         (see picture below and click to enlarge)
•      •  You may click here to order flow-meter and install in tube flange (see picture below)
•      •  KF25 Stainless steel Bellows 
•      •  KF25 Quick Clamps
  
  

                               

• 
       •   Limited by vacuum pump
•      •  50 mtorr can be achieved by mechanical pump
•      •  10^-5 torr can be reached by molecular pump
  
  
•      •     
  
•      •   Vacuum pump is not included, please order separately at related products section
  
  

• 
       •  10 feet length 10-3 AWG heavy duty UL approved power cable is included. Extra length cable can be
           ordered by click picture below-left
•      •  Plug is not included. You can order from your local hardware store according to female plug in your lab,
           or order from link below right (30A plug)

     
            (click here to order plugs from us)

• 
       •  In order to obtain accurate temperature inside tube furnace, you need to perform a temperature calibration before use,
          please click here to learn how.
•      •  How to set up ceramic tube and vacuum flange for MTI Tube furnace 
•      •  Proper placement of tube blocks
•      •  The tube furnaces with alumina tube are designed for using under vacuum and low pressure < 0.02 MPa / 0.2
          Bar/ 3 PSI
•      •  Attention: A two stage pressure regulator must be installed on gas cylinder to limit the pressure to
         below 3 PSI for safe operation. Click here to learn the installation of a gas regulator. 
•      •  Never heat the furnace while the gas release valve is closed and a positive pressure condition exists within
          the furnace chamber. The pressure gauge must be used to closely monitor the chamber condition at all times
          during the heating process; please open the gas release valve immediately once the chamber pressure has
          reached over 3 PSI to prevent unforseeable damages.
•      •  The flow rate for gasses should be limited to < 200 SCCM ( or 200ml/min )
•      •  Vacuum limit definition for all alumina tube furnaces: * Vacuum pressures may only be safely used up to
          1500°C
•      •  Two fiberous ceramic tube blocks are included for blocking heat radiation frominside tube (Ceramic blocks
           must be fully inserted into the furnace chamber before heating).